Today’s chandeliers are not just a lighting fixture,
However, they can also be used as decorative for interiors, and to setting up of a chandelier can be an easy task.
In this regard, J&S lighting furniture installers have documented the complete installation process for chandeliers, to ensure that those wanting to build chandeliers are able to learn!
1.Open the packaging and look over the contents according to instructions.
Chandeliers aren’t just for ornamental lighting, they also contain numerous accessories.
It’s not something you’re used to. Installers can confirm the components by following the instructions for installation.
If you discover a mistake in the place, you can contact the vendor promptly.
If the lighting installation host is packed in a box, the user must be present, and the installation is only guaranteed if there are no problems with the lighting.
2.Installation of chandelier
Assemble the lamp body and the surrounding lamp arms (where you’ll install the lamp).
After taking apart the light strip like the picture above, you’ll be able to determine where the arms of the light could be placed.
The lamp arms need to be fixed one by one using a wrench following the connection of the lamp arm. After installation the lamp arms require to be evenly distributed, otherwise, the installation is not complete. The chandelier needs to be angled towards the side with the bigger arm.
Connect the wires correctly on the lamp arm. Don’t connect the wrong wire. If, however, an LED bulb is used then it’s discovered that one of the light arms doesn’t illuminate and must be taken off for maintenance.
The chandelier and the lamp are currently being assembled. The top plate is installed.
5.Install the holder for your ceiling lamp to the position of installation you’ve chosen.
The procedure for installation is similar to installing a ceiling lamp. First, press the lamp holder against the hole, then pull out the hole. Next, make use of a drill to drill and install the expansion screw. Install the lamp holder.
6.Connect the power supply that is reserved for the ceiling to the chandelier’s power supply.
7.Then adjust the height of the chandelier. Finally, then assemble the chandelier’s accessories (glass bowl and shell) above the arm.
8.Finally put in the decorative cover (that is the cover that is placed on the base) then switch on the test power source to test whether the chandelier will start normal.
Also, pay close attention to the following points:
Fix chandelier on ceiling hole
First, the first method of installing a chandelier integrated. Install a sheet of metal on the ceiling. Then, fix several protruding braces onto the back side of the LED panel lights. Then, you can place the panel into the bracket that is in line with the metal sheet slot. The ceiling can be connected. The bracket and light surface must be adjusted to compensate for the height of the ceiling. Otherwise the LED panel could be mounted higher or lower.
The other method of installation is fixed. First, you need to install several screw holes in the ceiling, then move the light fixture intothe ceiling frame and install it onto the ceiling to attach the three sides. The panel light is put into the fixed slide-in mounting frame. The final side is fixed to the screw-mounted frame. Simple and simple.
The third installation method is a wire hanging one: first install the hanging wire part on the ceiling and lock the screws (the hanging wire was put in place at the factory.) The parts are suspended using the LED panel lighting. Installation and savings are easy. Ask the buyer whether they’d like to purchase an optional or standard suspension component.
Installation Precautions
- The product uses standard working voltage, please do not over-do the range of working voltage;
- Before installing, make sure that power has been switched off.
- Please carefully read the instructions before installing any device.
- Check to see if the product is waterproof, shockproof, and electricity-proof.
- This product is best only used indoors.
How do I install a chandelier that is integrated with the ceiling?
- Design the connection device using iron and wooden bricks to adjust the slop of the chandelier according to the error. You can use nails, screws or a combination. Following these steps, the chandelier installation is now almost completed.
- Pick the spot for the chandelier according to the height it is installed at in the living room. So you will avoid putting wires into the ceiling.
- The decorative materials must be incorporated prior to the structural layer. Ensure that the position is correct and maintain specific positions to allow for adjustments of the chandelier.
- You must join booms, slings and connecting devices.
The last point
In commercial buildings, installing chandeliers, particularly ones with low ceilings, is not recommended.
The majority of chandeliers currently available have a light source that radiates upwards. It is suggested you use them in conjunction with downlights or spotlights to create the traditional ceiling style.
GU10 bulbs for lighting are utilized in many chandeliers. They’re extremely powerful however they can be prone to breaking. The conventional E27 or E14 needs a larger lampshade and lamp head which is a bit low.
The installation of a practical, convenient chandelier is suggested. Of course, it is possible to also be set to alter the light level and temperature of the color.